D3 Teknik Elektronika Manufaktur
Permanent URI for this collectionhttps://repository.polibatam.ac.id/handle/PL029/1759
Browse
74 results
Search Results
Item Analysis Of Pin Needle Adapter Dynamics In The IGBT Module Endtest Process(2024-06-29) Mufriki,Achmad; Octowinandi,VivinNeedle Pin is a needle located on the dynamic adapter and functions to provide voltage to the IGBT module pins during the Endtest process. Many testing processes are not completed on time because some processes do not run according to schedule, especially in the Endtest process due to delays which result in long downtime, one of which is due to problems with testing dynamics. Damage to the dynamic adapter is mainly burnt and jammed needle pins. The author uses the fishbone method/Ishikawa diagram to find out the factors and root causes that cause burnt needle pins. The main root cause in this research is contaminated pins module. This research found that the value of P1 The average machine downtime before repair was 68.83 minutes, min 30 minutes and maximum 115 minutes and the percentage was 71.69%. And the value of P2 The average machine downtime after repairs was 55.08 minutes and the min was 20 minutes and the maximum was 85 minutes and the percentage was 57.37%. Based on the matrix, the comparison range for P1 and P2 is 14.32%.Item Discoloration issue analysis on smart7 product(2024-07-30) weni,kartika; arifin muhammaddiscoloration issueItem Analisis Mesin Neoceed JHT Testing Handler Untuk DSO 300 mil(Politeknik Negeri Batam, 2023-01-16) Siagian, Erwin Richard Tan; Gautama Aditya; Futra, Asrizal Deri; Arifin MuhammadPT Infineon Technologies Batam adalah perusahaan yang bergerak dibidang semikonduktor. Banyak perusahaan yang ingin maju dan bersaing untuk kualitas produknya demi memuaskan permintaan customer. PT. Infineon Technologies Batam membuat suatu produk semikonduktor seperti IC ( Integrated Circuit ), mikrokontroller dan smart card IC . Testing adalah sebuah proses pengujian electrical test pada sebuah package/device , yang dimana ini adalah salah satu proses terakhir (End of Line) pada process flow yang ada di PT. Infineon Technologies Batam. Terutama didepartemen TTI FT TC (Test Technologies and Innvovation, Final Test and Test Cell).Item Analisis Mesin Neoceed JHT Testing Handler Untuk DSO 300 mil(Politeknik Negeri Batam, 2023-01-16) Siagian Erwin Richard Tan; Gautama, Aditya; Futra, Asrizal Deri; Arifin MuhammadPT Infineon Technologies Batam adalah perusahaan yang bergerak dibidang semikonduktor. Banyak perusahaan yang ingin maju dan bersaing untuk kualitas produknya demi memuaskan permintaan customer. PT. Infineon Technologies Batam membuat suatu produk semikonduktor seperti IC ( Integrated Circuit ), mikrokontroller dan smart card IC . Testing adalah sebuah proses pengujian electrical test pada sebuah package/device , yang dimana ini adalah salah satu proses terakhir (End of Line) pada process flow yang ada di PT. Infineon Technologies Batam. Terutama didepartemen TTI FT TC (Test Technologies and Innvovation, Final Test and Test Cell).Item Perancangan Control Level Coupled Tank Menggunakan Metode Feedforward PI Abstrak(Politeknik Negeri Batam, 2022-07-15) Widianto, Ramadhin Valem; Kamarudin; Gautama Aditya; Pupista, Widya RikaDalam sebuah industri penggunaan tangki banyak digunakan untuk memenuhi kebutuhan proses produksi. Tangki tidak hanya digunakan sebagai media penyimpanan tetapi juga digunakan untuk menjaga kelancaran ketersediaan cairan yang diperlukan selama proses produksi berlangsung. Pentingnya penggunaan tangki secara terus mengharuskan pekerja mengontrol ketinggian cairan dalam tangki secara terus-menerus, tentu saja dalam proses pengontrolan yang dilakukan berulang kali menghabiskan banyak waktu dan tenaga pekerja dan memungkinkan terjadinya human error dalam sisi pencatatan data. Berdasarkan permasalahan diatas penulis memiliki tujuan untuk menciptakan sistem level control mengunakan sensor water pressure P255 dengan software CX Program agar dapat mengurangi terjadinya human error.Item Analysis Defect Alignment Out pada PCB saat proses Mounting(Politeknik Negeri Batam, 2023-01-16) Gultom,Fransiskus Juanda; Sani,AbdullahSurface Mount Technology atau sering disebut SMT merupakan teknologi terbaru yang digunakan untuk menempelkan komponen elektronik ke permukaan PCB. Komponen elektronik yang dapat dipasang oleh mesin SMT adalah komponen Surface Mount Device (SMD).Item Perancangan Control Level Coupled Tank Menggunakan Metode Feedforward PI(Politeknik Negeri Batam, 2022-07-15) Widianto, Ramadhin Valem; Kamarudin; Gautama Aditya; Puspita, Widya RikaDalam sebuah industri penggunaan tangki banyak digunakan untuk memenuhi kebutuhan proses produksi. Tangki tidak hanya digunakan sebagai media penyimpanan tetapi juga digunakan untuk menjaga kelancaran ketersediaan cairan yang diperlukan selama proses produksi berlangsung. Pentingnya penggunaan tangki secara terus mengharuskan pekerja mengontrol ketinggian cairan dalam tangki secara terus-menerus, tentu saja dalam proses pengontrolan yang dilakukan berulang kali menghabiskan banyak waktu dan tenaga pekerja dan memungkinkan terjadinya human error dalam sisi pencatatan data. Berdasarkan permasalahan diatas penulis memiliki tujuan untuk menciptakan sistem level control mengunakan sensor water pressure P255 dengan software CX Program agar dapat mengurangi terjadinya human error.Item Design and Set Up of Signal Light Inspection Tool Using Microcontroller Based on a Data Logger(Politeknik Negeri Batam, 2023-03-31) Panggabean, Ronni Lodiwik; Wijanarko, Heru; Maulidiah, Hana Mutialif; Prebianto, Nanta FakihPT Patlite Indonesia is a Warning Signal Lamp manufacturing industry that has grown rapidly since its inception. In the process of making signal lights, several processes are needed to ensure that the products produced are by ISO 9001: 2015 standards. One of the processes carried out in the industrial world is the inspection process. Inspection is a process carried out to ensure the quality of a product produced in accordance with standards, regulations, and customer satisfaction results. The use of a checksheet is one of the inspection processes carried out to assess the quality of the product produced. However, using check sheets to assess product quality requires a lot of time and effort in recording the results of each inspection. Therefore, a Signal Light Inspection Tool was designed using a Data Logger-Based Microcontroller that can store inspection data automatically. An inspection tool made using the data logger method to store data from signal light inspection results. This inspection tool has been successfully tested on 4 product models with productivity efficiency results of 111.8%. The inspection tool created has the advantage of being able to store the results of flow inspection data automatically, shorten production time and increase production output data.Item MISSPUNCH DEFECT ANALYSIS AND OPTIMIZATION IN AUTOVISION MACHINE(Politeknik Negeri Batam, 2023-03-31) Panggabean, Ronni Lodiwik T; Wijanarko, Heru; Maulidiah, Hana Mutialif; Prebianto, Nanta FakihPT Patlite Indonesia is a Warning Signal Lamp manufacturing industry that has grown rapidly since its inception. In the process of making signal lights, several processes are needed to ensure that the products produced are by ISO 9001: 2015 standards. One of the processes carried out in the industrial world is the inspection process. Inspection is a process carried out to ensure the quality of a product produced in accordance with standards, regulations, and customer satisfaction results. The use of a checksheet is one of the inspection processes carried out to assess the quality of the product produced. However, using check sheets to assess product quality requires a lot of time and effort in recording the results of each inspection. Therefore, a Signal Light Inspection Tool was designed using a Data Logger-Based Microcontroller that can store inspection data automatically. An inspection tool made using the data logger method to store data from signal light inspection results. This inspection tool has been successfully tested on 4 product models with productivity efficiency results of 111.8%. The inspection tool created has the advantage of being able to store the results of flow inspection data automatically, shorten production time and increase production output data.Item MISSPUNCH DEFECT ANALYSIS AND OPTIMIZATION IN AUTOVISION MACHINE(Politeknik Negeri Batam, 2023-01-16) Ihsan Miftahul; Jefiza, Adlian; Diono; Dwijotomo, AbdurahmanIn the era of technological globalization and the development of the manufacturing industry which is growing rapidly. Currently, companies in the manufacturing sector are continuously trying to improve the quality and quantity of products that will be produced and can last a long time to support the main needs for technology globally. Integrated Circuit (IC) is now needed for all kinds of electronic devices. PT Infineon Technologies Batam is one of the companies engaged in the manufacture of semiconductor electronic components and especially IC. The process to manufacture IC in PT Infineon has several steps which are Pre-Assembly - Die attach - Wire Bond - A2 Platting - Autovision - Molding - Platting - Marking - Trim & Form - Testing – Packing. From several steps mentioned above, Autovision is the process to mark defect in leadframe with the help of machine vision. However, sometime it causes another error because it incorrectly marks the leadframe. This project tries to reduce this issue by finding the potential problem using Fishbone diagram and SWOT analysis. Based from the analysis, the problem is caused by indexer parameter. After performing treatment to this root cause problem, the Autovision product defect have decreased from 2.7% to 0.7%.